F-000 Fire Defense

Fire-resistant homes, built without overspending.

The most cost-effective wildfire protection comes from a sealed, ember-resistant building envelope and smart assemblies — not automatically from the most expensive structural system. We help owners rebuilding in Altadena, Pacific Palisades and other wildland-urban interface areas put every construction dollar where it reduces fire risk.

F-100 The Real Threat

Embers first.

Wind-blown embers are a major cause of home ignitions in wildfires. Sealing the envelope and eliminating ember traps often delivers more protection per dollar than over-engineering the structural frame.

General guidance only. Material ratings, assembly performance, WUI compliance and insurance incentives must be verified against the applicable local building code, approved product listings, tested assembly documentation and current insurer requirements for each project. No upgrade guarantees code compliance, survival, insurance availability or a particular discount.

F-200 The Envelope

Often the most cost-effective protection.

Exterior materials and details decided early often add little cost — and help close the paths embers use to get in.

01

Siding

Fiber cement or three-coat stucco can provide a non-combustible exterior over conventional or steel framing, typically at lower cost than stone or brick.

02

Roofing

Class A architectural asphalt shingles over a fire-rated underlayment, with non-combustible metal drip edges, can achieve a Class A-rated assembly when installed per the tested listing — usually at lower upfront cost than standing-seam metal or clay tile.

03

Eaves + Soffits

Boxed-in eaves with non-combustible fiber cement soffits cover exposed rafter tails, a common ember entry point. Designed in from the start, they typically add little cost.

04

Vents

Tested, listed ember- and flame-resistant vents are designed to maintain required ventilation while resisting ember intrusion into attics and crawlspaces — usually a modest line item.

05

Windows + Doors

Consider dual-pane windows with tempered exterior glass where exposure is greatest; whether premium frames are warranted everywhere depends on the site and code. Solid-core or insulated steel exterior doors and sealed garage-door perimeters close common gaps.

F-300 Structure

Match the system to the project.

The right structural system depends on budget, schedule, seismic requirements, labor costs and the level of fire resistance the owner wants.

SystemFire performanceCost + value
Protected wood framingOne-hour fire-resistance-rated assemblies are possible using tested, listed wall assemblies, such as Type X gypsum.Typically the lowest upfront cost. Can perform well paired with a non-combustible exterior and enclosed eaves.
Cold-formed steel hybridNon-combustible structural framing.Often a strong middle ground on cost and performance. Pest-resistant, dimensionally stable, compatible with fiber cement and stucco.
Insulated concrete formsTwo- to four-hour ratings possible, depending on the tested assembly.Typically higher upfront cost; thermal mass may improve long-term energy performance.
Panelized / off-siteCan be engineered off-site to meet applicable WUI requirements.Can shorten the on-site schedule, reducing construction-loan carrying costs and waste.

Insulation: spray foam throughout isn't necessarily required for fire performance. On many projects, mineral wool in exterior walls and rim joists, standard fiberglass in interior partitions and continuous air sealing put performance where it counts — confirm with the project's designer and applicable code.

F-400 Design + Site

Simpler is often safer — and less costly.

Fire resistance doesn't stop at the exterior walls. Design geometry and the ground around the house matter as much as the materials.

Geometry

Simplify the roof

Fewer valleys, dormers and inside corners means fewer places for leaves and needles to collect — and less framing labor and roofing waste.

Zone 0

The first five feet

California's Board of Forestry is finalizing "Zone 0" ember-resistant regulations for the area immediately around homes in high fire hazard areas, aimed at keeping combustible materials away from the walls. Final requirements and timing are set by the state and local jurisdictions.

Insurance

Document every upgrade

Under the Department of Insurance's Safer from Wildfires framework, qualifying mitigation can earn discounts from participating insurers and the FAIR Plan. Eligibility and amounts vary — document every upgrade.

F-500 Priorities

Ten upgrades, in typical order.

When the budget is limited, this is where we often start. The right order depends on the site, the design and the applicable code.

  1. Ember-resistant vents
  2. Boxed-in eaves and soffits
  3. Class A roofing assembly
  4. Fiber cement siding or stucco
  5. Sealed windows, doors and garage openings
  6. Zone 0 non-combustible landscaping
  7. Mineral wool in exterior walls
  8. Simplified roof geometry
  9. Cold-formed steel hybrid framing
  10. Panelized construction
Every construction dollar should reduce fire risk. The best fire-resistant home isn't the one with the most expensive materials.

F-600 Primary Resources

Check the source.

General guidance only. Material ratings, assembly performance, WUI compliance and insurance incentives must be verified against the applicable local building code, approved product listings, tested assembly documentation and current insurer requirements for each project. No upgrade guarantees code compliance, survival, insurance availability or a particular discount.

Rebuilding in a fire zone?

Send your location and fire hazard zone, target size and stories, preferred structural system and budget. We'll prepare a prioritized material and assembly plan comparing cost, fire performance and long-term savings.